Відео

Thank you for posting this video! I just bought a 2004 F-250 with a bed that's been to hell and back. It needs to go. I was looking for options when I found your channel. I think I'll give this a try (or a version of this at least.) Well done. Subscribed.

did something similar to this for a old ranger I had. the center two floor/bed boards tho I put on hinges and didnt bolt them down but used a groove sorta like cabinets so they could sit flush. this way if I ever needed to get at the fuel pump I'd never have to drop the tank. after doing two fuel pumps on my other trucks, I will never ever drop a tank every again. so i wanted to be able to just flip open a small section of my bed and easily reach the fuel pump.

Ya couda changed the oil 8n the truck or dust crush up some charcoal in the mix

Sweet!

I realise this is an older video, but it might help if you cut a slot in the clamping piece. that way you can slide it on from the side and you don't have to remove the wing nut anymore since the rings can pass over it.

How is this holding up?

Nice to see a woodworker build a flat bed. So many folks have no woodworking skills.

Very cool restoration

a piece of angle-aluminum would improve the rigidity a lot.

Sir. I love it!!!!!!!!!!!!!! Im sendin you love❤ that is sooo awesome. I very respectfully wish to do the same.

How is the bed holding up after 4 years?

I think I'm going to copy this design, fantastic job man.

Were the floor boards just screwed into the wood frame? Flat bedding my 02 ranger.

I will be atempting this this summer. Thank you for the tutorial!!

Outstanding! Great tunes too ... thanks for sharing!

Awesome job!!!

Awesome job!!!

Awesome job!!!

Problem with this that's it already coast like a commercial samples

Chiming in from camp thumb cut due to Japanese pull saw. That thing is unforgiving. Opened me right up.

You should have squared the fence with the blade not table.

Tre-wax for me, appears to be more durable than Johnson’s. I think Tre-Wax dries with a harder finish. I’ve used it since 1962, trying many alternatives throughout the years.

VERY NICE

My goal has always been to get folks to think, even if it means folks figure out a way to make my designs better. Success! And let me know how it works out.

💪🏆 🌈

Why not use 1/2 inch on just the back piece. The back piece only runs against the runner. That way the side where you cut can still be the 1/4. That back piece is even the bigger of the 2.

Did your fuel nozzle cap area end up too low for fall into the tank? How did you support it under the bed?

I just bought a Chevy Colorado that I need to build a bed on your very informative

I looked through your videos and did not see how you made your baffle. I'll keep looking, but if you see this and feel like pushing me in the right direction it would be appreciated.

Man this looks great

Just use Evaporust to remove the rust. No rubbing. Then get it copper plated then Nickel electroplated. It will never rust again.

Where did you find those tail lights?

Very helpful video. Thanks.

Johnson’s Paste waxx is now >$140 a can.

Came out beautiful

Someone (me) got drunk and kicked a fat dent in the side of my truck ive always wanted a flatbed and figured id look it up see what other people did this looks great and is exactly what i want to do with mine

What a great design! I'm going to tweak it a bit for my lathe, but definitely will be building one of these. Thanks!

anyone in MD DC area want to build one on my F350?

You have inspired me to build somthing like this for my C 600 :)

A piece of cardboard works to keep rust off machines too. I think it stop the moisture in the air.

I would have left the sides off. Now your elbows will hit it.

GREAT JIG! I drilled 1/8" holes 1/2' deep, cut pins 1" long. Rubber bands roll off the pins and center on 1" thick rings!

Real late to the party, what depth did you cut to?

Much better than that plastic option I saw on related video Wood workers love wood End of

Of course you have the skills to align the holes. Next time, just drill the first hole all the way through, and using a larger diameter drill bit go through just the front. Do not go through it. This allows the screw heads to be recessed. Great job.

Love this. I have needed to upgrade my dust collection, this sure helps. You are right we have to do with what we have in the space that we have to work in.

No problem sexy hows your day

Looks awesome brother

Awesome job 👏🙏

Whats this weigh compared to original metal bed? Thanks